PIPELINE EQUIPMENT SOLUTIONS

Pipeline pig tracking equipment

Pipeline pig tracking equipment serves an important purpose: establishing where a pig or tool is and confirming its progress through the line. Different components contribute to this in different ways. A transmitter on the pig emits a signal, a locator or receiver follows that signal, fixed detectors confirm passage at defined points, and recording or communication equipment logs and reports those detections or positions. Manufacturers use these terms inconsistently, so the components chosen must be checked together, against the manufacturer’s documentation, to confirm that they work as one system and deliver the tracking outcome required.

Tremco Pipeline Equipment’s catalogue includes routes to transmitters, receivers, signallers and above-ground monitoring equipment. This page explains the equipment categories and the information needed for a useful enquiry without assuming that components from different systems are compatible.

Pipeline pig tracking requirements and equipment routes
Requirement Equipment route to review Important qualification
Generate a detectable signal from a pig or tool Transmitter Frequency, fit, service, runtime and approval requirements are model-specific
Find or follow a transmitter-equipped pig or tool Portable or vehicle-supported receiver/locator Detection performance depends on the complete system and deployment conditions
Confirm passage at a defined pipeline point Passage signaller Intrusive and non-intrusive products have different installation and project requirements
Record or communicate information along a route Above-ground marker or connected monitoring product Data, power and communications functions vary by model and configuration

This table is a category guide, not a compatibility or installation decision.

Explore tracking-equipment categories

CDI TRAXALL 770 tracking receiver

02

Tracking receivers and locators

Receivers are used to detect, locate or monitor a compatible transmitter or tool signal. Start with the CDI tracking receiver range and SPY pig tracker range. Model capabilities, software, accessories, approvals and compatibility must be verified for the intended deployment.

CDI CD52 Bandit pig passage signaller

03

Pig passage signallers

Passage signallers provide confirmation at a defined point rather than performing the same role as a portable tracking receiver. Browse CDI pigging signallers and review the applicable product source for the installation, indication and output requirements.

CDI QUBE above-ground marker

04

Above-ground markers and monitoring

Above-ground markers can provide location, passage-recording or communications functions according to the selected system. Review the CDI above-ground marker route and identify the required local, recorded or remote output in the enquiry.

Information to provide with a tracking-equipment enquiry

Include the information that is available and appropriate to disclose:

  • the pig, inspection tool or other item to be detected;
  • the required outcome: locate, follow, confirm passage, log an event or communicate a result;
  • pipeline material, nominal dimensions and available wall/burial information;
  • terrain, access and intended deployment points;
  • expected run distance and duration;
  • known transmitter, receiver, signal or frequency information;
  • whether monitoring is fixed, portable or vehicle-supported;
  • required local indication, data recording, connectivity or notification;
  • environmental, hazardous-area or project-approval requirements;
  • project location and required timing; and
  • any existing system components that must be assessed for compatibility.

Final component selection must follow the applicable current manufacturer documentation and project review.

Tracking equipment does not replace selection of the physical pig, its components or the launch-and-receive arrangement. For those requirements, use the broader pigging-equipment pathway.

Explore pipeline pigging equipment

Technical information and current product routes

Questions about pig tracking equipment

What is the difference between a pig tracker and a passage signaller?

A tracking system generally helps detect or locate a compatible transmitter-equipped pig or tool. A passage signaller indicates passage at its installation point; the detectable pig or tool and any transmitter requirement depend on the selected model. Products, terminology and outputs vary, so the required function and system components must be confirmed together.

Do all transmitters work with all receivers?

No universal compatibility should be assumed. Frequency, signal type, tool arrangement, pipeline conditions, firmware, accessories and model-specific requirements may affect the system. Check current manufacturer documentation for the exact components.

What is an above-ground marker used for?

Depending on the product and configuration, an above-ground marker may identify a monitoring location and record or communicate passage or location information. Confirm the required data, connectivity, deployment and compatibility rather than relying on the category name alone.

Can Tremco Pipeline Equipment identify a system from the pipeline diameter alone?

Pipeline diameter is only one input. The tool, required outcome, material, burial and terrain, run duration, existing components, approvals, connectivity and operating context may all be relevant to the assessment.

Discuss a pig tracking requirement

Provide the equipment already in use, the outcome required, available pipeline and route information, project location and timing. Tremco Pipeline Equipment can then direct the enquiry to the relevant product family and current technical source.

For hire enquiries about Traxall 770 and X Series transmitters, view our confirmed equipment hire offering. Contact us to confirm current availability

Discuss a pig tracking requirement

Browse CDI tracking equipment