Pipe Bevelling Equipment
01Prepare the edge
Bevelling creates an angled pipe-end preparation for the weld joint.
02Guide the cut
Band, chain and other machine arrangements guide the cutting setup around the pipe.
03Compare the setup
Review pipe dimensions, required preparation, drive and access before narrowing the options.
Pipe bevelling equipment prepares an angled edge on the end of a pipe before welding. The bevel creates space for the weld joint, while guided cutting equipment helps produce a consistent preparation around the pipe. Sawyer’s range includes band, chain, quick-set and compact machines for pipe cutting and weld-end preparation.
Browse the equipment below, then compare the options and enquiry requirements. Selection depends on the pipe dimensions, material, preparation, access and operating method—not diameter alone.
Compare the equipment
The following summary is a navigation aid, not a model-selection
decision. Check each product against the current manufacturer document
and quoted configuration.
Model 206 Band Beveling
Machine
The Sawyer
Model 206 Band Beveling Machine uses a flexible band to guide a
crawler and torch-holder arrangement around the pipe. Check the available band sizes and crawler compatibility against the current Model 206 documentation.
Consider the actual outside diameter, band, crawler, drive
arrangement, torch holder, accessories, pipe surface and available
clearance during review.
Quick Set Beveling Machine
The Sawyer
Quick Set Beveling Machine provides a separate equipment route for
defined cutting and bevelling requirements. Confirm the current machine
size, adjustment range, torch arrangement, drive option, clearance and
preparation requirement from the applicable Sawyer information.
Compact Beveling Machine
The Sawyer
Compact Beveling Machine is another distinct equipment family.
Review current size information, handling requirements, drive, torch
setup, access and site constraints rather than treating it as
interchangeable with the Band or Quick Set routes.
MX1 Beveling Machine
The Sawyer
MX1 Beveling Machine uses a chain-and-gear arrangement. Confirm the
chain or guide configuration, pipe condition, orientation, drive, torch
holder, access and current manufacturer documentation.
Information needed to
narrow the options
Include the following information with the enquiry:
- required task: cutting, bevelling or both;
- required pipe-end preparation or approved weld-preparation
detail; - actual pipe outside diameter and relevant inside-diameter
information; - wall thickness, material and pipe condition;
- coating, seam, spiral weld or out-of-round condition where
relevant; - work position and pipe orientation;
- radial and axial clearance around the work area;
- preferred drive arrangement where the project has defined one;
- torch and fuel or plasma requirements already defined by the
project; - power and compressed-air constraints where relevant;
- hot-work, access and environmental controls;
- required accessories and technical documents; and
- location, quantity and required timing.
Tremco Pipeline Equipment can use these details to identify the applicable Sawyer
information and clarify further review requirements. The responsible
project parties remain accountable for the procedure, hot-work controls,
setup, operator competence, inspection and weld-preparation
acceptance.
Bevelling,
cold cutting and pipe facing are distinct routes
These guided thermal cutting and bevelling routes are distinct from
cold-cutting and machining equipment.
- Explore
Sawyer cold-cutting equipment where a cold-cutting route is being
evaluated. - Explore
Darby pipe-facing machines where a machining or pipe-facing route is
being evaluated. - Browse
Sawyer construction equipment for alignment, handling, support and
other construction-equipment routes. - Browse pipeline construction
equipment for the wider catalogue. - Explore all pipeline equipment
solutions
The approved work procedure and competent technical review determine
the appropriate method.
Technical resources
Use the current product page and manufacturer document for the
selected family:
- Sawyer
Model 206 Band Beveling Machine - Sawyer
Quick Set Beveling Machine - Sawyer
Compact Beveling Machine - Sawyer
MX1 Beveling Machine - Sawyer manufacturer
downloads
Part numbers, ranges, accessories and technical limits must be
checked against current manufacturer information before quotation or
use.
Questions about pipe
bevelling equipment
Which pipe
measurement is needed for an enquiry?
Provide the actual outside diameter and the available wall,
inside-diameter and material information—not only the nominal pipe size.
Also provide the required preparation, access, clearance, orientation
and site constraints.
Are “bevelling”
and “beveling” different processes?
No. Australian copy normally uses bevelling, while
Sawyer uses the American spelling beveling in its
product naming.
Is
bevelling equipment the same as cold-cutting equipment?
Not necessarily. The equipment routes use different cutting or
machining methods and have different project requirements. The approved
work procedure determines which method should be evaluated.
Can one
model be selected from pipe diameter alone?
No. Diameter is only one input. Wall and material information,
preparation, surface condition, clearance, orientation, drive, torch
arrangement and site controls can all affect the equipment and
configuration requiring review.
Discuss a pipe
cutting or bevelling requirement
Send the pipe dimensions, material, required preparation, access and
clearance, intended method, site conditions, location and timing to
Tremco Pipeline Equipment.
